Materials / Tungsten carbide
Tungsten carbide
Extreme wear resistance for mold inserts, punches and dies — machined by EDM and diamond grinding.
Tungsten carbide (WC-Co) is the material of choice when a tool or insert must survive millions of cycles without losing size. With hardness of HRA 88–92 it cannot be milled economically, so parts are produced by wire EDM, die-sinking EDM and diamond grinding. Typical applications are injection mold inserts, stamping punches, drawing dies and wear plates, held to ±0.002 mm.
Grades we machine
| YG8 (K20) | 8% cobalt, HRA 89.5. General purpose for wear parts, punches and small dies with good toughness. |
|---|---|
| YG15 (K40) | 15% cobalt, HRA 87.5. Higher impact resistance for stamping punches and cold heading dies. |
| YG20 / YG25 | 20–25% cobalt. Maximum toughness for heavy stamping and high-impact tooling. |
| Sub-micron grades | 0.4–0.8 µm grain size for mirror-polish mold inserts and precision punches. |
Machining notes
Wire EDM first
Wire EDM cuts carbide after sintering with no mechanical force, so there is no cracking risk. Multiple trim passes produce Ra 0.4 µm and ±0.002 mm accuracy; fine wire (0.1–0.2 mm) cuts small internal radii.
Diamond grinding for flats and edges
Flats, rake faces and precision edges are ground with diamond wheels on surface and optical projection grinders after EDM. This removes the recast layer and holds flatness and parallelism.
Stress and micro-cracks
Carbide is brittle, so EDM parameters are controlled to limit the recast layer and micro-cracks. Critical edges are finished by grinding and inspected under magnification.
Assembly and preload
Inserts are machined with the shrink-fit or press-fit allowance required for the mold pocket, and can be supplied with matched sleeves or backing plates.
Capability and finishes
| Dimensional tolerance | ±0.002 mm typical; ±0.001 mm on precision features |
|---|---|
| Surface roughness | Ra 0.4 µm after EDM; Ra 0.1 µm after diamond grinding |
| Machining methods | Wire EDM, die-sinking EDM, diamond surface / cylindrical grinding |
| Hardness range | HRA 87.5–92 (YG8 to sub-micron grades) |
| Lead time | 7–15 working days for production; 5–8 days for samples |
Available finishes
- Diamond grinding
- EDM trim passes
- Laser marking
- Edge honing
- Polishing (sub-micron grades)
Typical applications
- •Injection mold inserts and cores
- •Stamping punches and dies
- •Drawing and extrusion dies
- •Wear plates and guide rails
- •Cutting blades and slitters
- •Precision bushings and sleeves
Frequently asked questions
Can tungsten carbide be CNC milled?
Only in the soft (green) state before sintering, which is not suitable for precision parts. Sintered carbide at HRA 88–92 is machined by wire EDM, die-sinking EDM and diamond grinding — that is why carbide parts cost more than steel parts of the same size.
What tolerance and finish can you achieve on carbide?
Wire EDM holds ±0.002 mm with Ra 0.4 µm, and diamond grinding improves flatness and surface finish to Ra 0.1 µm. For critical edges we EDM, then grind, then inspect under magnification to remove the recast layer.
How do I choose between YG8 and YG15?
Choose YG8 (8% cobalt) for wear resistance in low-impact mold inserts and small punches. Choose YG15 or YG20 when the tool sees impact or heavy stamping loads, because the higher cobalt content improves toughness at some cost in wear resistance.
Send your drawing for a free quote
Tungsten carbide parts machined to your drawing, from 1 piece. Quote and DFM feedback within 24 hours.