Materials / Titanium

Titanium

Highest strength-to-weight ratio of the common metals — and the most demanding to machine.

Titanium is chosen for aerospace, medical implants and chemically aggressive environments where aluminium would corrode and steel would be too heavy. Grade 5 (Ti-6Al-4V) delivers roughly 900 MPa tensile strength at 4.4 g/cm³, but it conducts heat poorly and work-hardens, so cutting speed is low, coolant pressure is high and tool wear must be watched. Expect 7–15 working days for production orders.

Grades we machine

Grade 2 (commercially pure)Excellent corrosion resistance and formability. Used for chemical equipment, heat exchangers and medical instruments.
Grade 5 / Ti-6Al-4VThe workhorse alloy: about 900 MPa tensile strength. Aerospace brackets, medical implants, fasteners and racing components.
Grade 9 (Ti-3Al-2.5V)Lower strength, better ductility. Used for tubing, hydraulic lines and bicycle frames.
Grade 23 (Ti-6Al-4V ELI)Extra-low interstitial variant for medical implants; improved fracture toughness and biocompatibility.

Machining notes

Heat and tool life

Titanium conducts heat poorly, so heat concentrates at the cutting edge. We use high-pressure coolant, sharp uncoated or AlTiN-coated carbide and conservative cutting speeds to protect tool life and surface integrity.

Chatter and thin walls

Low stiffness and strong vibration tendency make thin titanium walls difficult. Trochoidal milling, light radial engagement and fixture damping keep walls stable down to about 1 mm.

Work hardening and surface integrity

A damaged surface layer can initiate cracks in aerospace parts. Finishing passes remove the work-hardened layer, and surfaces can be inspected for alpha-case and micro-cracks on request.

Tolerance and inspection

Titanium parts are measured with CMM at controlled temperature. Tolerances of ±0.01 mm are standard, with ±0.005 mm achievable on critical features.

Capability and finishes

Dimensional tolerance±0.01 mm standard; ±0.005 mm on critical features
Surface roughnessRa 0.8–1.6 µm as machined; Ra 0.4 µm after finishing
Material certificatesEN 10204 3.1 mill certificates supplied
Lead time7–15 working days for production; 5–8 days for samples
Minimum order1 piece — no MOQ

Available finishes

  • Passivation (ASTM F86)
  • Bead blasting
  • Anodizing (Type II / Type III)
  • Laser marking
  • Polishing
  • Electropolishing

Typical applications

  • •Aerospace brackets and structural parts
  • •Medical implants and surgical instruments
  • •Chemical processing equipment
  • •Marine and offshore components
  • •Motorsport and high-performance fasteners
  • •Heat exchangers and tubing

Frequently asked questions

Why is titanium more expensive to machine than aluminium?

Titanium cuts at roughly one-fifth the speed of aluminium, wears tooling faster and needs high-pressure coolant and rigid fixturing. Material cost is also higher. A titanium part can cost 4–8 times an equivalent aluminium part, so it is specified only where strength, weight or corrosion resistance justify it.

Can you machine medical-grade titanium (Grade 23)?

Yes. Grade 23 (Ti-6Al-4V ELI) is machined for implant and instrument components with material certificates, passivation to ASTM F86 and full dimensional reports. Cleanliness and surface integrity are documented for medical customers.

What tolerance can you hold on titanium?

Standard tolerance is ±0.01 mm and critical features reach ±0.005 mm. Because titanium distorts with heat, parts are machined with coolant, stress-relieved where needed and inspected on a CMM at controlled temperature.

Send your drawing for a free quote

Titanium parts machined to your drawing, from 1 piece. Quote and DFM feedback within 24 hours.