Blog / CNC surface finish guide: what Ra values actually mean

CNC surface finish guide: what Ra values actually mean

Which finish each process reaches, how to call it out on a drawing, and what it costs

KaiMi Engineering Team · · 7 min read

Surface finish is specified on almost every drawing and understood on very few. Ra 1.6 and Ra 0.4 look like arbitrary numbers, but they decide whether a part needs a second operation, a grinding step or a polishing pass. This guide maps Ra values to real processes and explains how to specify finish only where it changes how the part works.

What Ra measures

Ra is the arithmetic average roughness of a surface profile, measured in micrometres (µm) over a sampling length. A lower Ra means a smoother surface. It says nothing about waviness or form — a part can have excellent Ra and still be visibly out of flat.

Roughness is measured per ISO 4287 and normally reported as Ra. Where a drawing needs peak-height control (sealing faces, for example) specify Rz or Rmax instead, because a few tall peaks can leak even when the average is low.

Which process reaches which finish

ProcessTypical RaBest achievableNotes
CNC millingRa 1.6–3.2 µmRa 0.8 µmVisible tool marks; finer with a finishing pass
CNC turningRa 1.6–3.2 µmRa 0.8 µmFeed marks depend on nose radius and feed rate
Surface grindingRa 0.4–0.8 µmRa 0.1 µmAdds an operation; required for hardened parts
Wire EDMRa 0.4 µmRa 0.1 µmImproves with multiple trim passes
Bead blastingRa 1.6–3.2 µm—Uniform matte look; can hide tool marks
PolishingRa 0.1 µmRa 0.05 µmManual or robotic; cost scales with area

How to specify finish on a drawing

  • Put a general note in the title block, for example "all surfaces Ra 3.2 µm unless otherwise specified".
  • Call out tighter finish only on functional surfaces, with the ISO 1302 symbol and the Ra value.
  • For sealing faces, specify both roughness and flatness — roughness alone does not prevent leaks.
  • For cosmetic parts, define what "cosmetic" means: which faces are visible and what defects are acceptable.
  • Avoid mixing Ra and Rz on the same drawing unless you really mean different things.

What each step costs

The pattern is consistent: every step below Ra 0.8 µm adds a separate process, and separate processes add handling, inspection and risk of damage. If the surface does not seal, slide, reflect or carry a coating, Ra 3.2 µm is usually enough.

RequirementCost impactLead time
As machined Ra 3.2 µmBaselineStandard
Finishing pass to Ra 1.6 µm+5–10%+0–1 day
Grinding to Ra 0.4 µm+20–35%+2–3 days
Polishing to Ra 0.1 µm+30–60%+2–5 days
Anodizing or coating+10–25%+3–5 days

When finish matters more than tolerance

Hydraulic and pneumatic sealing faces, optical mounts, bearing journals and food-contact surfaces are usually finish-critical; their dimensional tolerance is often looser than the finish requirement.

In those cases, spending the budget on grinding or polishing is better than tightening a dimensional tolerance that does not affect performance.

Finishes that change the surface, not just the roughness

  • Anodizing grows the surface by roughly half the coating thickness per side — account for it on tight-tolerance parts.
  • Powder coating adds 60–120 µm and cannot be used on mating or threaded features.
  • Electropolishing removes a few micrometres and improves Ra by smoothing peaks; it is common on stainless medical parts.
  • Laser marking and engraving are cosmetic and do not affect Ra unless they overlap a functional surface.

About the author

KaiMi Engineering Team — 30+ mechanical engineers and quality inspectors at our Dongguan plant, writing about machining capability, tolerances and sourcing for OEM buyers. More about KaiMi.

Frequently asked questions

What is a good surface finish for CNC machined parts?

Ra 3.2 µm is the normal as-machined finish and is acceptable for most non-functional surfaces. Specify Ra 1.6 µm for visible parts, Ra 0.8 µm for sliding or mating faces, and Ra 0.4 µm or better only for sealing surfaces, bearings or optical components.

Can CNC milling achieve Ra 0.4 µm?

Milling reaches about Ra 0.8 µm with a finishing pass. Ra 0.4 µm usually requires grinding or polishing after milling, which is a separate operation with its own cost and lead time.

Does anodizing improve surface roughness?

No. Anodizing adds an oxide layer that follows the existing surface profile, so it does not smooth the part. If the finish requirement is below the as-machined value, the part must be polished or ground before anodizing.

Send your drawing for a free quote

Free DFM feedback and a drawing-based quotation within 24 hours. No minimum order quantity.