Blog / Aluminium vs stainless steel: which material fits your part?
Aluminium vs stainless steel: which material fits your part?
Strength, corrosion, machinability and landed cost compared for the two most common CNC materials
KaiMi Engineering Team · · 8 min read
Most CNC parts are either 6061-T6 aluminium or 304/316L stainless steel, and the choice is usually decided by three questions: does it need to resist corrosion, how much load does it carry, and what is the budget? This comparison gives the numbers behind those questions so the decision is made once, correctly, instead of after the first rejected batch.
Quick comparison
| Property | Aluminium 6061-T6 | Stainless 304 / 316L |
|---|---|---|
| Tensile strength | ~310 MPa | ~505 MPa (304), ~485 MPa (316L) |
| Density | 2.70 g/cm³ | 8.00 g/cm³ |
| Machinability | Excellent (reference 100) | Moderate (~45 for 304, ~40 for 316L) |
| Corrosion resistance | Good; needs anodizing outdoors | Excellent, 316L for chlorides |
| Typical tolerance | ±0.01 mm | ±0.01 mm |
| Relative part cost | 1.0× | 2.2–3.2× |
| Lead time | 3–7 days samples | 5–10 days production |
Why stainless costs two to three times more
It is not only the raw material. Stainless steel work-hardens, so cutting speeds drop to roughly a third of aluminium and tool life shortens. That means more machine hours per part, more tooling cost and, for medical or food parts, an extra passivation step.
Weight matters too. A stainless part is about three times heavier, which increases freight cost on air shipments. For a 2 kg aluminium assembly, the stainless equivalent is 6 kg — often a bigger cost difference than the machining itself.
Choose aluminium when…
- Weight matters: drones, robot arms, automation fixtures, portable equipment.
- The part is an enclosure, bracket, plate or heat sink with moderate loads.
- You need fast prototypes — aluminium machines roughly three times faster.
- The environment is indoor or the part will be anodized or painted.
- You need complex geometry with thin walls, where cutting forces must stay low.
Choose stainless steel when…
- The part sees water, salt, cleaning chemicals or sterilisation.
- It is medical, food-processing, pharmaceutical or marine equipment.
- Loads are high relative to the cross-section, or fatigue life matters.
- The surface must resist abrasion and keep a clean, hygienic finish.
- The part will be welded into a stainless assembly.
Finishing changes the calculation
Aluminium usually needs a finish to survive outdoors: clear anodizing for indoor parts, hard anodizing for wear surfaces, powder coating for colour. Those steps add cost but are cheap relative to machining.
Stainless steel is often left as machined or bead blasted, with passivation for medical and food use. Electropolishing gives the cleanest surface but adds a process step and lead time.
When to use neither
If the part needs extreme wear resistance, tungsten carbide is the answer — machined by wire EDM and diamond grinding rather than milling. If it needs high strength at high temperature, titanium Grade 5 is the usual candidate, at four to eight times the cost of aluminium.
Plastics are the other side of the trade: PEEK and POM machine quickly and insulate electrically, but creep under sustained load and expand more with temperature.
A decision sequence that works
- 1. Is there moisture, salt or cleaning chemical? If yes → stainless (316L if chlorides).
- 2. Is weight or speed of delivery critical? If yes → aluminium 6061-T6.
- 3. Is the highest load close to the material limit? If yes → stainless or 7075 aluminium.
- 4. Is wear the dominant failure mode? → consider carbide or a hardened steel.
- 5. Otherwise → 6061-T6 with anodizing is almost always the cheapest correct answer.
About the author
KaiMi Engineering Team — 30+ mechanical engineers and quality inspectors at our Dongguan plant, writing about machining capability, tolerances and sourcing for OEM buyers. More about KaiMi.
Frequently asked questions
Is 6061 or 7075 aluminium better for machining?
6061-T6 machines more easily, anodizes evenly and costs less; use it by default. 7075-T6 reaches about 570 MPa tensile strength for high-load parts, but it is less corrosion resistant and needs a protective finish.
Can aluminium replace stainless steel in a marine part?
Only with the right alloy and protection. 5083 or 6061 with hard anodizing can work above the waterline, but immersed or splash-zone parts should be 316L stainless or duplex, because aluminium pits quickly in chlorides once the oxide layer is damaged.
How much does material choice change the quote?
For the same geometry, stainless steel parts typically cost 2.2–3.2 times the aluminium equivalent once machining time, tooling and freight are included. The gap grows for parts with many features or thin walls, because stainless demands slower cutting and more rigidity.
Send your drawing for a free quote
Free DFM feedback and a drawing-based quotation within 24 hours. No minimum order quantity.